home

Networking

NetworkingStorageSoftwareSupport and Services
NetworkingStorageSoftwareSupport and Services

Celestica Documentation Portal

Find your product documents here

Show Contents

thumbnailNetworking

Hardware Description

LEDs

LED behavior and status indications for system, port, and power supply components.

Table 1. LED Status Types

System Status LEDs

Four bi-colored LEDs on the front of the unit indicate overall system status (FAN, PSU, ALM, SYS)

RJ45 Network Ports

Each port supports two LEDs to indicate link, traffic, and PoE status

QSFP28 Uplink Ports

Each port supports four bi-colored LEDs to indicate link and traffic status

RJ45 / SFP Combo

Management Ports

RJ45 port supports two LEDs to indicate link and traffic status

SFP port supports one LED to indicate link and traffic status

PSUs

Each power supply supports a single bi-colored LED to indicate status

Table 2. System Status LED Descriptions
Indicator LEDSignStateDescription
Power StatusPWR / PSUGreen SolidBoth PSUs operating normally
Amber SolidOne PSU abnormal or lost input
OffSystem is powered off
Fan StatusFANGreen SolidAll fan modules operating normally
Amber SolidOne or more fans abnormal
OffSystem is powered off
Alarm StatusALMGreen SolidNo alarm active
Amber SolidCritical alarm
Amber 4Hz BlinkingMajor alarm
Amber 1Hz BlinkingMinor alarm
System StatusSTATAlternating Green/Amber 1HzSystem operating normally
Table 3. Network Port LEDs
Indicator LEDDescription

Indicator LED

Description

Combo RJ45

Management Port

1x bi-color Green/Amber LED on the left side and one green LED on the right side.

  1. Use the left side dual-color LED to indicate the Link status:
  1. Port link active in 1000M mode: Green On
  2. Port link active in 10/100M mode: Amber On
  3. Port link down: LED Off
  1. Use the right-side single-color LED to indicate the Activity status:
    1. Port link active and there is traffic: Green blinking
    2. Port has no traffic: LED off

Combo SFP

Management Port

1x i-color Green/Amber LED for SFP port.

  1. For port link at GbE mode:
    1. Port link up: Green ON
    2. Port link activity: Green Blink
    3. Port link down: LED Off
  2. For port link at 10/100MbE mode:
    1. Port link up: Amber ON
    2. Port link activity: Amber Blink
    3. Port link down: LED Off

QSFP28 Port

4x Bi-color Green/Amber LED for each SFP28 port.

  1. For the port link at 25GbE mode:
    1. Port link up (1x100G): LED #1 Green ON
    2. Port link up (2x50G): LED #1 and #3 Green ON
    3. Port Link up (4x25G): LED #1-4 Green ON
    4. Port link activity: Green Blink (Respective ON LEDs)
    5. Port link down: LEDs Off
  2. For port link at 1/10GbE mode:
    1. Port link up (1x40G): LED #1 Amber ON
    2. Port link up (2x20G): LED #1 and #3 Amber ON
    3. Port Link up (4x1G/10G): LED #1-4 Amber ON
    4. Port link activity: Amber Blink (Respective ON LEDs)
    5. Port link down: LEDs Off

RJ45 Data Ports

24/48x PoE Data ports – 10GBase-T, based on RJ45 physical interface.

One Bi-color Green/Amber LED on the left side and one Bi-color Green/Amber LED on the right side.

  1. Use the left side dual-color LED to indicate link status:
    1. Port link active in 10G mode: Green On
    2. Port link active in >10G mode: Amber On
    3. Port link is down: LED Off
  2. Use the right side dual-color LED to indicate the Act status and PoE status:
    1. Port link active and there is traffic: Blink LED (Green or Amber per PoE State)
    2. Port PoE power Disabled: Green ON
    3. Port PoE power enabled: Amber ON
    4. Port PoE power denied: Alternate Blink Amber/Green for 1 minute, then return to normal operation
  3. Port has no traffic: LED off
Note:

Table 4. PSU LEDs
Indicator LEDRear Panel sign

Rear Panel sign

State

Description

550W PSU Module

P-1/P-2

Green LED on

PSU output ON and OK

Amber LED on

PSU failure or

AC in power lost, but a second power is powered

Off

PSU module is powered off

1600W PSU &

920W PSU Module

P-1/P-2
  1. Left LED(DC OK) Green on
  2. Right LED(AC OK) Green on

Power supply DC outputs on and OK

  1. Left LED(DC OK) is Green/0.5Hz flashing
  2. Right LED(AC OK) Green on

AC present / Only standby outputs on

  1. Left LED(DC OK) Red on
  2. Right LED(AC OK) Green on

Power supply failure, PSU shut down

  1. Left LED(DC OK) Green on
  2. Right LED(AC OK) is Red 0.5Hz flashing

One PSU is working normally, but the AC power supply of the other PSU is abnormal.

Port type

SKU-ID

Description

Combo

RJ45

ES2010 & DS2010 -All SKU
  • 10/100/1000Mbps auto negotiation
  • MDI/MDI-X cable mode auto negotiation
  • Copper Interface based on RJ45 physical connector

SFP

  • 1000Mbps auto negotiation
  • Optical Interface based on SFP physical connector

Serial Console port

ES2010 & DS2010 -All SKU
  • Support 9600 and 115200(default) baud rates, eight data bits, one stop bit, and no parity

USB Port

ES2010-24CP

ES2010-48CP

DS2010
  • USB 3.0 host type A interface

QSFP28

ES2010 & DS2010 -All SKU

2/6x QSFP28 interface

  • Full Compliance with QSFP28 MSA specifications
  • Compliant to IEEE 40GBase-SR/LR/CR and 100GBase-SR/LR/CR, OIF (CEI-25G-VSR) Support for 2.0W modules (SFF-8419 Power Class III)

25Gbps Electrical Specifications

  • Support for 5.0W modules (SFF-8679 Power Class 7)
  • ES2010-48CP/ DS2010: Support for 9.0W modules (SFF-8679 Power Class 8) on at least one port - ES2010-24CP: Support for 7.0W modules (SFF-8679 Power Class 8) on at least one port
  • Passive DAC performance up to 5m@25Gbps operation
  • Passive DAC performance up to 7m@10Gbps/Lane operation

RJ45 data port

DS2010

ES2010-48CP
  • Port 1-48: 10/100/1000Mbps/10Gbps auto negotiation
  • All ports support PoE Type 4 Class 8

ES2010-24C

ES2010-24CP
  • Port 1-24: 10/100/1000Mbps/10Gbps auto negotiation
  • All ports support PoE Type 4 Class 8

Last updated: October 21, 2026